d do not scale from this print lsem-1xx-xx.x-x-dv-a-x-xx-tr no of positions 20,30,40,50 dv: dual vertical lead style * -02.5 -03.0 -04.0 -06.0 plating specification packaging(see note 6) -tr: tape & reel shield * -s: with shield (not available with *-wt) -n: no shield option -k: polyimide film (use k-500-300,see fig. 3, sht 3) *-wt: weld tab (use wt-36-xx-t, see fig. 4, sht 3) (not available with *-s) * = not tooled -a: alignment pin tail option "a" "a" c 0.10[.004] 0.80 typ .031 "c" ref "d" d see note 4 01 02 c pin n 1.32 ref .052 0.95 ref .037 (no of position x .80[.031])-.80[.031] 1.32 ref .052 "e" ref 1.10 ref .043 "a" "b" 0.85 ref .033 c 0.87 0.10 .034 .004 0.670 0.10 .0264 .004 section "a"-"a" scale 5 : 1 c c (lsem-1xx-xx.x-x-dv-a-n-xx shown) fig 1 c f: flash selective, 3 au / 50 ni min on contact, matte tin tail l: light selective, 10 au / 50 ni min on contact, matte tin tail (values given are in micro-inches) sheet of unless otherwise specified, dimensions are in millimeters[inches]. tolerances are: decimals angles x.x: 0.3 [.01] 2 x.xx: 0.13 [.005] x.xxx: 0.051 [.0020] material: 0.8mm pitch terminal/socket combo by: lsem-1xx-xx.x-x-dv-a-x-xx-tr dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing chadp 04/01/2009 3 1 sheet scale: 2:1 insulator: black lcp, ul 94 vo contact or terminal: phos bronze shield: stainless steel f:\dwg\misc\mktg\lsem-1xx-xx.x-x-dv-a-x-xx-tr-mkt.slddrw notes: 1. represents a critical dimension. 2. burr allowance: .038 [.0015]. 3. minimum pushout force; terminals: 2.22 n [.5 lbs], contacts: 2.22 n [.5 lbs]. 4. when mating with another lsem-dv, 01 will mate with contact 02 on mating connector. when mating with a lsem-dh, pin 01 will mate with pin n, where n = total number of positions. 5. measure from top of vertical wall. 6. for quantities up to 49 pcs., no leader , trailer or reel will be supplied. for quantities of 50-124 pcs., no leader or trailer will be supplied. 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322 revision d
"g" 0.20 .008 ref c 0.80 .031 02 01 see note 4 1.65 .065 0.80 ref .031 4.98 ref .196 2.00[0.079] c * lsem-1xx-xx.x-x-dv-a-s shown (same as fig1 different as shown) (* =not tooled) fig 2 -s option sh40-20-01-dv-n c sheet of 0.8mm pitch terminal/socket combo by: lsem-1xx-xx.x-x-dv-a-x-xx-tr dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing chadp 04/01/2009 3 2 sheet scale: 1:0.2 f:\dwg\misc\mktg\lsem-1xx-xx.x-x-dv-a-x-xx-tr-mkt.slddrw revision d 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
"k" ref 0.13 ref .005 *lsem-120-03.0-x-dv-a-s-k shown (same as fig 2 different as shown) (* =not tooled) fig 3 -k option 5.50 .217 "h" 0.45 .018 d c "l" ref "m" "n" wt-36-xx-t (see table 4) fig 4 *-wt option * lsem-1xx-xx.x-x-dv-a-s-wt shown (same as fig 1 different as shown) (* =not tooled) (* =not tooled) (* = not tooled) sheet of 0.8mm pitch terminal/socket combo by: lsem-1xx-xx.x-x-dv-a-x-xx-tr dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. chadp 04/01/2009 3 3 sheet scale: 5:1 f:\dwg\misc\mktg\lsem-1xx-xx.x-x-dv-a-x-xx-tr-mkt.slddrw do not scale drawing revision d 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail info@samtec.com code 55322
|
